Jan 17 2013

Label Design with Inkscape

The 2" x 4" product label was also designed with Inkscape. The embedded QR code was . . . show detail

The 2" x 4" product label was also designed with Inkscape. The embedded QR code was first generated with command line qrencode then imported into Inkscape. Originally, the QR code image was generated in PNG format then automatically traced with Inkscape's Trace Bitmap command. However, qrencode can also generated QR code in EPS format without the need for trace conversion.


Jan 17 2013

Laser Cutting

Compared to CNC machining, laser cutting has a shorter development time because . . . show detail

Compared to CNC machining, laser cutting has a shorter development time because the cut/engrave patterns are design in a free form drawing program(Inkscape) and interfaces with the laser engraver via the print function.

An ULS M300 35Watt CO2 laser engraver was used to cut and engrave the US made clear Acrylite FF extruded sheets.


Jan 16 2013

Cover & Floor Plate Design

Inkscape was used to design the acrylic components for laser cutting and engraving. . . . show details

Inkscape was used to design the acrylic components for laser cutting and engraving. Earlier Raspberry Pi boards do not have mounting holes. Therefore, an acrylic floor is used in place of machined standoffs.

The top cover profile was based on the 2D dxf drawn earlier with LibreCAD. GPIO and venting openings were added in Inkscape. For the acrylic standoff, the profile was also based on the 2D dxf drawing. The back of the Raspberry Pi pcb was scanned, then rotated and resized in GIMP before importing into Inkscape. The cutout for the bottom components were added in Inkscape using the scanned pcb image as reference.

A few design iterations were needed to get the dimensions right, especially for the floor board. The acrylic thickness is .118" and is tall enough to ensure none of the bottom solder leads contacts the aluminum case.


Jan 15 2013

CNC Machining

Usually a few machining iterations are required to proof the G-code program and to fine tune the machining parameters. TuxCASE for Raspberry Pi uses simple . . . show detail

Usually a few machining iterations are required to proof the G-code program and fine tune the machining parameters. TuxCASE for Raspberry Pi uses simple front and back operations to minimize setup time. The machining operations use two Kurt D675 vises. There are cheaper alternatives, but the D675 manual vise is the least expensive of the domestically made machine vises. The left vise is for machining the top of the case and the right vise is for machining the bottom of the case. This setup allows for one complete case to be machined with each program cycle.

Sometimes, the tool path offsets are incorrectly calculated, or the tool length offset is too short for part, or the work piece was not clamped securely. Usually the part is scraped, but in some unfortunate events, the cutting tool is scraped.

Bellow are some of the unpleasant mishaps.


Jan 14 2013

G-Code Writing with Geany

The G-code program is grouped by tools and each tools has sub sections representing a machining operation. For example, . . . show detail

The G-code program is grouped by tools and each tools has sub sections representing a machining operation. For example, The first group of machining operation is performed by the 2.5" facing mill. The 2.5" face mill has two sub sections. First is the face milling of the bottom surface on the right vise and the second is face milling of the top surface on the left vice.

Machining Operations:

  • 2.5" Face Mill
    • Right Vise - Face bottom of case
    • Left Vise - Face top of case
  • 3/8" Roughing End Mill
    • Right Vise - Profile bottom half of case
    • Right Vise - Machine HDMI opening
    • Right Vise - Machine Power and SD card opening
    • Left Vise - Profile top half of case
    • Left Vise - Machine pocket for RPi board [ tool path generated by VisualMill ]
  • 3/8" Ball End Mill
    • Left Vise - Machine RCA Video opening
  • 5/16" Ball End Mill
    • Left Vise - Machine Audio opening
  • 3/8" 120 Degree Chamfer Mill
    • Left Vise - Spot drill cover screw holes
    • Left Vise - Chamfer top profile of case
    • Right Vise - Chamfer bottom profile of case
  • #43 Drill
    • Left Vise - Drill cover screw holes
  • 4-40 Tap
    • Left Vise - Tap cover screw holes
  • #32 Drill
    • Left Vise - Drill bottom mounting holes
  • 1/4" 100 Degree Chamfer Mill
    • Left Vise - Chamfer bottom mounting holes
  • 1/16" Ball End Mill
    • Left Vise - Engrave Serial Number

Jan 13 2013

2D Drawing with LibreCAD

LibreCAD was used to generate the dimensional drawing for TuxCASE_RPi. The case dimensions are . . . show details

LibreCAD was used to generate the dimensional drawing for TuxCASE_RPi. The case dimensions are necessary for writing the G-code program that will will be used by the CNC controller to machine the aluminum block into the final shape of TuxCASE.

LibreCAD was also used to layout the extra tool paths that are needed. For example, the SD Card and USB Power slots are too deep for the 3/8" end mill to machine effectively in a single pass. Therefore, a couple extra machining passes are needed. Those extra tool path are generated with LibreCAD's line offset tool.


Jan 13 2013

3D Model with FreeCAD

The 3 dimensional model of TuxCASE for Raspberry Pi was made with FreeCAD for visual inspection. The open source FreeCAD follows a . . . show detail

The 3 dimensional model of TuxCASE for Raspberry Pi was made with FreeCAD for visual inspection. The open source FreeCAD follows a workflow similar to commercial software where 2 dimensional drawings are turned into 3 dimensional shape through basic extrude operation. Multiple 3 dimensional object can then be combined or subtracted to construct the final 3D model.

The 2D drawing from FreeCAD can also be exported as DXF to be opened in LibreCAD for tool path calculation.

Note: Currently, FreeCAD v13r1335 is metric only. However, LibreCAD can convert the FreeCAD generated DXF file from millimeter to inch.


May 22 2012

Initial Production Summary

TThe initial batch of the bottle opener has been completed and mailed out. After numerous revisions, only . . . show details

The initial batch of the bottle opener has been completed and mailed out. After numerous revisions, only 12 pieces of blanks were left for the final revision. Therefore, out of 100 blanks only 12 acceptable bottle openers were produced.

There first couple revisions had too shallow of a mouth opening that caused the bottle opener to peel the edges ofthe bottle cap. Subsequent revisions were made to lengthen as well as deepen the mouth opening to give better mechanical leverage. Electrochemical etching was inconsistent and was replaced with direct laser marking.


May 04 2012

Haas SR-100 Vacuum Table

A two way solenoid valve was installed to enable the control, through CNC Controller M-Code, of opening and closing the pneumatic 5C collect chuck.  A roller lever switch, wired in parallel, was also added to the boot padel, to enable manual control.


Apr 26 2012

Bottle Opener Revision 5

The mouth opening was increased from a radius to .100" to .110" to better accommodate taller caps.